2010 Mazda CX-9 CX9 Radio Audio Bose Wiring Schematic Diagram Colors Install

Here is the stereo radio wiring information for your 2010 Mazda CX-9 CX9 body with the standard or Bose amplified systems. It will be useful when installing an aftermarket radio, sound stereo system, or other automotive accessories. Make sure to grab the appropriate tools to test all the wires in your CX-9. Please check it over and use it as a GUIDE to help you locate the appropriate wires. This schematic is provided free of charge and may not be 100% accurate. Failure to properly test all the wires may lead to vehicle or bodily damage. All information is provided as-is and accuracy is not guaranteed.

2010 Mazda CX-9 CX9 Radio Audio Bose Wiring Diagram Schematic Colors Install
2010 Mazda CX-9 CX9 Radio Stereo Audio Bose Wiring Diagram Schematic Colors Install

If you find any conflicting info please leave a comment with what you found in your Mazda CX-9. If you don’t see the audio radio wiring diagram you need comment and we will try to add it ASAP. Thanks for looking!

2010 Mazda CX-9 Audio Wiring Radio Diagram Schematic Colors – Aftermarket Stereo Installation Help

Car Radio Constant 12v+ Wire: Red/Blue @ Radio Harness
Car Stereo Ground Wire: Black @ Radio Harness
Car Radio Ignition Switched Wire: Pink/Blue @ Radio Harness

Reverse / Backup Wire: Red/Yellow (+) Driver Kick BCM or harness to rear

Car Radio Illumination Wire: Red/Black @ Main Radio Harness

Car Radio Amp Turn On Wire: Purple/White @ 24-pin radio connector pin 6

Car Stereo Power Antenna: N/A @ Main Radio Harness

Non-Bose Speaker Wires At Radio:

Left Front Speaker (+) Positive: Dark Blue/Orange
Left Front Speaker (-) Negative: Purple

Right Front Speaker (+) Positive: Gray/Blue
Right Front Speaker (-) Negative: Yellow/Green

Left Rear Speaker (+) Positive: Green
Left Rear Speaker (-) Negative: Green/Black

Right Rear Speaker (+) Positive: Yellow/Black
Right Rear Speaker (-) Negative: Yellow

SPEAKER WIRE COLORS AT AMP IN THE RIGHT REAR QUARTER PANEL

Left Front Door Speaker Wire (+) Positive: Blue/Orange
Left Front Door Speaker Wire (-) Negative: Purple

Left Front Tweeter Speaker Wire (+) Positive: Red/White
Left Front Tweeter Speaker Wire (-) Negative: Red/Yellow

Right Front Door Speaker Wire (+) Positive: Gray/Blue
Right Front Door Speaker Wire (-) Negative: Yellow/Green

Right Front Tweeter Speaker Wire (+) Positive: Blue/White
Right Front Tweeter Speaker Wire (-) Negative: Blue/Red

Left Rear Door Speaker Wire (+) Positive: Green
Left Rear Door Speaker Wire (-) Negative: Green/Black

Right Rear Door Speaker Wire (+) Positive: Yellow/Black
Right Rear Door Speaker Wire (-) Negative: Yellow

Subwoofer Speaker Wire Positive / Negative: N/A

Center Channel Speaker Wire Positive / Negative: N/A

Retain OEM AUX In Center Console – 16-pin Connector at Back of Radio

Take a normal rca cable and cut one end off leaving yourself RCAs and a foot or two of slack. Strip the left and right ends twist the common shields together and then connect them to the following wires:

OEM AUX Left (+) Positive: White/Blue
OEM AUX Right (+) Positive: Red/Blue
OEM AUX Common Shield: Green/White (either green/white in this plug will work they are common)

Radio Size: Single or Double Din

Radio Removal Tools: – Dash Removal Plastic Pry Tools – Use these tools to help carefully unclip and remove both side panels from center radio trim panel. Carefully remove the shifter trim panel. Remove 1 screw from the trim panel with the power port then remove the panel. Remove 1 screw on the side of each vent holding the main radio trim panel on. Remove the main trim panel then remove 4 screws and pull the radio.

If you are installing a new aftermarket radio in your CX9 you need the wiring harness, the antenna adapter, steering wheel control module, and the mounting kit as well.

REQUIRED PARTS FOR AFTERMARKET RADIO INSTALL

MOUNTING KIT FOR SINGLE or DOUBLE DIN AFTERMARKET RADIOS:

WIRING HARNESS:

This harness can be used with the non-bose or bose systems. It will also retain your steering wheel controls no need for a separate adapter! Further yet no need to relocate the OEM radio for setting the clock functions or scrolling through the MPG – all can be done from the steering wheel!

ANTENNA ADAPTER:

N/A – Not needed

STEERING WHEEL CONTROLS ADAPTER:

Not needed if using the wiring harness above, otherwise this one below is great!

Metra Axxess ASWC-1 Universal Steering Wheel Control Interface

SPEAKER WIRING ADAPTERS:

N/A

Adding A Backup Camera:

We’ve had great luck with this camera for a nice rear view. Mounted on the OEM lip above the license plate you see just a hair of the bumper in the image so you can really dial in your parking.

RECOMMENDED TOOLS FOR THE INSTALL – SAME ONES THE PROS USE!

– 3M Electrical Tape

– Dash Removal Plastic Pry Tools

– Install Bay Butt Connectors

– Gardner Bender Auto Wire Stripper

– Klein Wire Cutters / Crimpers

Leave a Reply

Your email address will not be published. Required fields are marked *