Category Archives: Audio Stereo Wiring Diagram

2006 Honda Ridgeline Audio Radio Wiring Diagram Schematic Colors

Here is the stereo radio wiring information for your 2006 Honda Ridgeline with the standard or amplified systems. It will be useful when installing an aftermarket radio, sound stereo system, or other automotive accessories. Make sure to grab the appropriate tools to test all the wires in your Ridgeline. Please check it over and use it as a GUIDE to help you locate the appropriate wires. This schematic is provided free of charge and may not be 100% accurate. Failure to properly test all the wires may lead to vehicle or bodily damage. All information is provided as-is and accuracy is not guaranteed.

2006 Honda Ridgeline Audio Wiring Radio
2006 Honda Ridgeline Audio Wiring Radio

If you find any conflicting info please leave a comment with what you found in your 2006 Honda Ridgeline. If you don’t see the audio radio wiring diagram you need comment and we will try to add it ASAP. Thanks for looking!

(MAKE SURE TO SCROLL TO THE BOTTOM TO SEE IF ANY OTHER READERS POSTED ANY OTHER TIPS AND TRICKS!)

2006 Honda Ridgeline Audio Wiring Radio Diagram Schematic Colors

Car Radio Constant 12v+ Wire: White – Pin 10
Car Stereo Ground Wire: Black – Pin 20
Car Radio Ignition Switched Wire: Yellow/Red Pin 2 @ Radio Harness

Car Stereo VSS Speed Wire: N/A
Car Stereo Reverse Wire + : Green (+) @ Light
Car Stereo Dimmer Wire: Red @ Pin 19
Car Radio Illumination Wire: Red/Black (Parking Lights) @ Pin 9
Car Stereo Power Antenna: Black (+) Pin 3 @ Antenna Plug
Car Radio Amp Turn On Wire: N/A

Left Front Speaker Wire (+) Positive: Light Green – Pin 8
Left Front Speaker Wire (-) Negative: Violet – Pin 18
Right Front Speaker Wire (+) Positive: Blue – Pin 7
Right Front Speaker Wire (-) Negative: Red – Pin 17

Left Rear Speaker Wire (+) Positive: Brown/White – Pin 6
Left Rear Speaker Wire (-) Negative: Red/Yellow – Pin 16
Right Rear Speaker Wire (+) Positive: Red/Blue – Pin 5
Right Rear Speaker Wire (-) Negative: Yellow – Pin 15

Center Channel Speaker Wire Positive / Negative: N/A

Subwoofer Speaker Wire Positive / Negative: Yellow/Black & Light Green/Red

These wires let you keep your OEM aux jack to work with your new aftermarket radio. Grab a cheap RCA Auxiliary Cable plug either the aux or the rcas into the back of your new aftermarket radio depending on what type of audio input they have. Then cut off the other end and splice into the following wires at the 14-pin connector found behind the radio:

OEM AUX Audio Left Signal: White @ 6 pin connector pin 5
OEM AUX Audio Left Ground: Red @ 6 pin connector pin 4
OEM AUX Audio Right Signal: Brown @ 6 pin connector pin 3
OEM AUX Audio Right Ground Red @ 6 pin connector pin 4

Radio Size: Single or Double Din

Speaker Size Front: 6.5″
Speaker Size Rear: 6.5″
Speaker Size Subwoofer: 8″

Use the adapters below to install common 6.5″ speakers in the doors. Depending on the size and depth of speakers you still may need to cut some of the door metal away. Use some tin snips to easily get the job done.

Check out these Infinity Reference 6.5-Inch speakers they work great and are an excellent bang for the buck! Or the component version if you want to replace your OEM tweeters in the dash as well.

Radio Removal: Using plastic bezel removal tools carefully pop the radio bezel from the dash. Unplug all the connectors and remove the dash bezel. The radio and pocket below is then held in with 5 screws.

Keep in mind if you are installing a new radio you need the mounting kit, the wiring harness, the antenna adapter, and the steering wheel control adapter if you have audio controls on the wheel you want to keep.

REQUIRED PARTS FOR AFTERMARKET RADIO INSTALL

WIRING HARNESS:

ANTENNA ADAPTER FOR INSTALL:

GRAY MOUNTING KIT FOR DOUBLE DIN AFTERMARKET RADIOS:

TAN MOUNTING KIT FOR DOUBLE DIN AFTERMARKET RADIOS:

GRAY MOUNTING KIT FOR SINGLE DIN AFTERMARKET RADIOS:

TAN MOUNTING KIT FOR SINGLE DIN AFTERMARKET RADIOS:

CUSTOM UNDER SEAT BOX ENCLOSURE FOR ADDING AFTERMARKET SUB WOOFER:

SPEAKER WIRING ADAPTER FOR INSTALL:

Use these if you don’t want to tap in or cut off your existing speaker connectors. They plug right in then right on to the new speaker making installation a breeze. Order quantity 2 if doing front and rear speakers.

STEERING WHEEL CONTROLS ADAPTER:

Metra Axxess ASWC-1 Universal Steering Wheel Control Interface

RECOMMENDED TOOLS FOR THE INSTALL – SAME ONES THE PROS USE!

– Gardner Bender Auto Wire Stripper

– Klein Wire Cutters / Crimpers

– 3M Electrical Tape

– Install Bay Butt Connectors

– Dash Removal Plastic Pry Tools

2007 Honda Ridgeline Audio Radio Wiring Diagram Schematic Colors

Here is the stereo radio wiring information for your 2007 Honda Ridgeline with the standard or amplified systems. It will be useful when installing an aftermarket radio, sound stereo system, or other automotive accessories. Make sure to grab the appropriate tools to test all the wires in your Ridgeline. Please check it over and use it as a GUIDE to help you locate the appropriate wires. This schematic is provided free of charge and may not be 100% accurate. Failure to properly test all the wires may lead to vehicle or bodily damage. All information is provided as-is and accuracy is not guaranteed.

2007 Honda RIdgeline Audio Radio Wiring DIagram
2007 Honda RIdgeline Audio Radio Wiring DIagram

If you find any conflicting info please leave a comment with what you found in your 2007 Honda Ridgeline. If you don’t see the audio radio wiring diagram you need comment and we will try to add it ASAP. Thanks for looking!

(MAKE SURE TO SCROLL TO THE BOTTOM TO SEE IF ANY OTHER READERS POSTED ANY OTHER TIPS AND TRICKS!)

2007 Honda Ridgeline Audio Wiring Radio Diagram Schematic Colors

Car Radio Constant 12v+ Wire: White – Pin 10
Car Stereo Ground Wire: Black – Pin 20
Car Radio Ignition Switched Wire: Yellow/Red Pin 2 @ Radio Harness

Car Stereo VSS Speed Wire: N/A
Car Stereo Reverse Wire + : Green (+) @ Light
Car Stereo Dimmer Wire: Red @ Pin 19
Car Radio Illumination Wire: Red/Black (Parking Lights) @ Pin 9
Car Stereo Power Antenna: Black (+) Pin 3 @ Antenna Plug
Car Radio Amp Turn On Wire: N/A

Left Front Speaker Wire (+) Positive: Light Green – Pin 8
Left Front Speaker Wire (-) Negative: Violet – Pin 18
Right Front Speaker Wire (+) Positive: Blue – Pin 7
Right Front Speaker Wire (-) Negative: Red – Pin 17

Left Rear Speaker Wire (+) Positive: Brown/White – Pin 6
Left Rear Speaker Wire (-) Negative: Red/Yellow – Pin 16
Right Rear Speaker Wire (+) Positive: Red/Blue – Pin 5
Right Rear Speaker Wire (-) Negative: Yellow – Pin 15

Center Channel Speaker Wire Positive / Negative: N/A

Subwoofer Speaker Wire Positive / Negative: Yellow/Black & Light Green/Red

These wires let you keep your OEM aux jack to work with your new aftermarket radio. Grab a cheap RCA Auxiliary Cable plug either the aux or the rcas into the back of your new aftermarket radio depending on what type of audio input they have. Then cut off the other end and splice into the following wires at the 14-pin connector found behind the radio:

OEM AUX Audio Left Signal: White @ 6 pin connector pin 5
OEM AUX Audio Left Ground: Red @ 6 pin connector pin 4
OEM AUX Audio Right Signal: Brown @ 6 pin connector pin 3
OEM AUX Audio Right Ground Red @ 6 pin connector pin 4

Radio Size: Single or Double Din

Speaker Size Front: 6.5″
Speaker Size Rear: 6.5″
Speaker Size Subwoofer: 8″

Use the adapters below to install common 6.5″ speakers in the doors. Depending on the size and depth of speakers you still may need to cut some of the door metal away. Use some tin snips to easily get the job done.

Check out these Infinity Reference 6.5-Inch speakers they work great and are an excellent bang for the buck! Or the component version if you want to replace your OEM tweeters in the dash as well.

Radio Removal: Using plastic bezel removal tools carefully pop the radio bezel from the dash. Unplug all the connectors and remove the dash bezel. The radio and pocket below is then held in with 5 screws.

Keep in mind if you are installing a new radio you need the mounting kit, the wiring harness, the antenna adapter, and the steering wheel control adapter if you have audio controls on the wheel you want to keep.

REQUIRED PARTS FOR AFTERMARKET RADIO INSTALL

WIRING HARNESS:

ANTENNA ADAPTER FOR INSTALL:

GRAY MOUNTING KIT FOR DOUBLE DIN AFTERMARKET RADIOS:

TAN MOUNTING KIT FOR DOUBLE DIN AFTERMARKET RADIOS:

GRAY MOUNTING KIT FOR SINGLE DIN AFTERMARKET RADIOS:

TAN MOUNTING KIT FOR SINGLE DIN AFTERMARKET RADIOS:

CUSTOM UNDER SEAT BOX ENCLOSURE FOR ADDING AFTERMARKET SUB WOOFER:

SPEAKER WIRING ADAPTER FOR INSTALL:

Use these if you don’t want to tap in or cut off your existing speaker connectors. They plug right in then right on to the new speaker making installation a breeze. Order quantity 2 if doing front and rear speakers.

STEERING WHEEL CONTROLS ADAPTER:

Metra Axxess ASWC-1 Universal Steering Wheel Control Interface

RECOMMENDED TOOLS FOR THE INSTALL – SAME ONES THE PROS USE!

– Gardner Bender Auto Wire Stripper

– 3M Electrical Tape

– Klein Wire Cutters / Crimpers

– Install Bay Butt Connectors

– Dash Removal Plastic Pry Tools

2008 Honda Ridgeline Audio Radio Wiring Diagram Schematic Colors

Here is the stereo radio wiring information for your 2008 Honda Ridgeline with the standard or amplified systems. It will be useful when installing an aftermarket radio, sound stereo system, or other automotive accessories. Make sure to grab the appropriate tools to test all the wires in your Ridgeline. Please check it over and use it as a GUIDE to help you locate the appropriate wires. This schematic is provided free of charge and may not be 100% accurate. Failure to properly test all the wires may lead to vehicle or bodily damage. All information is provided as-is and accuracy is not guaranteed.

2008 Honda Ridgeline Audio Radio Wiring
2008 Honda Ridgeline Audio Radio Wiring

If you find any conflicting info please leave a comment with what you found in your 2008 Honda Ridgeline. If you don’t see the audio radio wiring diagram you need comment and we will try to add it ASAP. Thanks for looking!

(MAKE SURE TO SCROLL TO THE BOTTOM TO SEE IF ANY OTHER READERS POSTED ANY OTHER TIPS AND TRICKS!)

2008 Honda Ridgeline Audio Wiring Radio Diagram Schematic Colors

Car Radio Constant 12v+ Wire: White – Pin 10
Car Stereo Ground Wire: Black – Pin 20
Car Radio Ignition Switched Wire: Yellow/Red Pin 2 @ Radio Harness

Car Stereo VSS Speed Wire: N/A
Car Stereo Reverse Wire + : Green (+) @ Light
Car Stereo Dimmer Wire: Red @ Pin 19
Car Radio Illumination Wire: Red/Black (Parking Lights) @ Pin 9
Car Stereo Power Antenna: Black (+) Pin 3 @ Antenna Plug
Car Radio Amp Turn On Wire: N/A

Left Front Speaker Wire (+) Positive: Light Green – Pin 8
Left Front Speaker Wire (-) Negative: Violet – Pin 18
Right Front Speaker Wire (+) Positive: Blue – Pin 7
Right Front Speaker Wire (-) Negative: Red – Pin 17

Left Rear Speaker Wire (+) Positive: Brown/White – Pin 6
Left Rear Speaker Wire (-) Negative: Red/Yellow – Pin 16
Right Rear Speaker Wire (+) Positive: Red/Blue – Pin 5
Right Rear Speaker Wire (-) Negative: Yellow – Pin 15

Center Channel Speaker Wire Positive / Negative: N/A

Subwoofer Speaker Wire Positive / Negative: Yellow/Black & Light Green/Red

These wires let you keep your OEM aux jack to work with your new aftermarket radio. Grab a cheap RCA Auxiliary Cable plug either the aux or the rcas into the back of your new aftermarket radio depending on what type of audio input they have. Then cut off the other end and splice into the following wires at the 14-pin connector found behind the radio:

OEM AUX Audio Left Signal: White @ 6 pin connector pin 5
OEM AUX Audio Left Ground: Red @ 6 pin connector pin 4
OEM AUX Audio Right Signal: Brown @ 6 pin connector pin 3
OEM AUX Audio Right Ground Red @ 6 pin connector pin 4

Radio Size: Single or Double Din

Speaker Size Front: 6.5″
Speaker Size Rear: 6.5″
Speaker Size Subwoofer: 8″

Use the adapters below to install common 6.5″ speakers in the doors. Depending on the size and depth of speakers you still may need to cut some of the door metal away. Use some tin snips to easily get the job done.

Check out these Infinity Reference 6.5-Inch speakers they work great and are an excellent bang for the buck! Or the component version if you want to replace your OEM tweeters in the dash as well.

Radio Removal: Using plastic bezel removal tools carefully pop the radio bezel from the dash. Unplug all the connectors and remove the dash bezel. The radio and pocket below is then held in with 5 screws.

Keep in mind if you are installing a new radio you need the mounting kit, the wiring harness, the antenna adapter, and the steering wheel control adapter if you have audio controls on the wheel you want to keep.

REQUIRED PARTS FOR AFTERMARKET RADIO INSTALL

WIRING HARNESS:

ANTENNA ADAPTER FOR INSTALL:

GRAY MOUNTING KIT FOR DOUBLE DIN AFTERMARKET RADIOS:

TAN MOUNTING KIT FOR DOUBLE DIN AFTERMARKET RADIOS:

GRAY MOUNTING KIT FOR SINGLE DIN AFTERMARKET RADIOS:

TAN MOUNTING KIT FOR SINGLE DIN AFTERMARKET RADIOS:

CUSTOM UNDER SEAT BOX ENCLOSURE FOR ADDING AFTERMARKET SUB WOOFER:

SPEAKER WIRING ADAPTER FOR INSTALL:

Use these if you don’t want to tap in or cut off your existing speaker connectors. They plug right in then right on to the new speaker making installation a breeze. Order quantity 2 if doing front and rear speakers.

STEERING WHEEL CONTROLS ADAPTER:

Metra Axxess ASWC-1 Universal Steering Wheel Control Interface

RECOMMENDED TOOLS FOR THE INSTALL – SAME ONES THE PROS USE!

– Gardner Bender Auto Wire Stripper

– 3M Electrical Tape

– Install Bay Butt Connectors

– Klein Wire Cutters / Crimpers

– Dash Removal Plastic Pry Tools

2009 Honda Ridgeline Audio Radio Wiring Diagram Schematic Colors

Here is the stereo radio wiring information for your 2009 Honda Ridgeline with the standard or amplified systems. It will be useful when installing an aftermarket radio, sound stereo system, or other automotive accessories. Make sure to grab the appropriate tools to test all the wires in your Ridgeline. Please check it over and use it as a GUIDE to help you locate the appropriate wires. This schematic is provided free of charge and may not be 100% accurate. Failure to properly test all the wires may lead to vehicle or bodily damage. All information is provided as-is and accuracy is not guaranteed.

2009 Honda RIdgeline Radio Audio Wiring
2009 Honda RIdgeline Radio Audio Wiring

If you find any conflicting info please leave a comment with what you found in your 2009 Honda Ridgeline. If you don’t see the audio radio wiring diagram you need comment and we will try to add it ASAP. Thanks for looking!

(MAKE SURE TO SCROLL TO THE BOTTOM TO SEE IF ANY OTHER READERS POSTED ANY OTHER TIPS AND TRICKS!)

2009 Honda Ridgeline Audio Wiring Radio Diagram Schematic Colors

Car Radio Constant 12v+ Wire: White – Pin 24
Car Stereo Ground Wire: Black – Pin 12
Car Radio Ignition Switched Wire: Yellow/Red Pin 14 @ Radio Harness

Car Stereo VSS Speed Wire: N/A
Car Stereo Reverse Wire + : Green (+) @ Light
Car Stereo Dimmer Wire: Red @ Pin 1
Car Radio Illumination Wire: Red/Black (Parking Lights) @ Pin 13
Car Stereo Power Antenna: Black (+) Pin 3 @ Antenna Plug
Car Radio Amp Turn On Wire: N/A

Left Front Speaker Wire (+) Positive: Light Green – Pin 23
Left Front Speaker Wire (-) Negative: Violet – Pin 22
Right Front Speaker Wire (+) Positive: Blue – Pin 19
Right Front Speaker Wire (-) Negative: Red – Pin 18

Left Rear Speaker Wire (+) Positive: Brown/White – Pin 11
Left Rear Speaker Wire (-) Negative: Red/Yellow – Pin 10
Right Rear Speaker Wire (+) Positive: Red/Blue – Pin 7
Right Rear Speaker Wire (-) Negative: Yellow – Pin 6

Center Channel Speaker Wire Positive / Negative: N/A

Subwoofer Speaker Wire Positive / Negative: Yellow/Black & Light Green/Red

These wires let you keep your OEM aux jack to work with your new aftermarket radio. Grab a cheap RCA Auxiliary Cable plug either the aux or the rcas into the back of your new aftermarket radio depending on what type of audio input they have. Then cut off the other end and splice into the following wires at the 14-pin connector found behind the radio:

OEM AUX Audio Left Signal: White @ 14 pin connector pin 1
OEM AUX Audio Left Ground: Red @ 14 pin connector pin 2
OEM AUX Audio Right Signal: Brown @ 14 pin connector pin 8
OEM AUX Audio Right Ground Red @ 14 pin connector pin 2

Radio Size: Single or Double Din

Speaker Size Front: 6.5″
Speaker Size Rear: 6.5″
Speaker Size Subwoofer: 8″

Use the adapters below to install common 6.5″ speakers in the doors. Depending on the size and depth of speakers you still may need to cut some of the door metal away. Use some tin snips to easily get the job done.

Check out these Infinity Reference 6.5-Inch speakers they work great and are an excellent bang for the buck! Or the component version if you want to replace your OEM tweeters in the dash as well.

Radio Removal: Using plastic bezel removal tools carefully pop the radio bezel from the dash. Unplug all the connectors and remove the dash bezel. The radio and pocket below is then held in with 5 screws.

Keep in mind if you are installing a new radio you need the mounting kit, the wiring harness, the antenna adapter, and the steering wheel control adapter if you have audio controls on the wheel you want to keep.

REQUIRED PARTS FOR AFTERMARKET RADIO INSTALL

WIRING HARNESS:

GRAY MOUNTING KIT FOR DOUBLE DIN AFTERMARKET RADIOS:

TAN MOUNTING KIT FOR DOUBLE DIN AFTERMARKET RADIOS:

GRAY MOUNTING KIT FOR SINGLE DIN AFTERMARKET RADIOS:

TAN MOUNTING KIT FOR SINGLE DIN AFTERMARKET RADIOS:

ANTENNA ADAPTER FOR INSTALL:

CUSTOM UNDER SEAT BOX ENCLOSURE FOR ADDING AFTERMARKET SUB WOOFER:

SPEAKER WIRING ADAPTER FOR INSTALL:

Use these if you don’t want to tap in or cut off your existing speaker connectors. They plug right in then right on to the new speaker making installation a breeze. Order quantity 2 if doing front and rear speakers.

STEERING WHEEL CONTROLS ADAPTER:

Metra Axxess ASWC-1 Universal Steering Wheel Control Interface

RECOMMENDED TOOLS FOR THE INSTALL – SAME ONES THE PROS USE!

– Gardner Bender Auto Wire Stripper

– 3M Electrical Tape

– Install Bay Butt Connectors

– Klein Wire Cutters / Crimpers

– Dash Removal Plastic Pry Tools

2010 Honda Ridgeline Audio Radio Wiring Diagram Schematic Colors

Here is the stereo radio wiring information for your 2010 Honda Ridgeline with the standard or amplified systems. It will be useful when installing an aftermarket radio, sound stereo system, or other automotive accessories. Make sure to grab the appropriate tools to test all the wires in your Ridgeline. Please check it over and use it as a GUIDE to help you locate the appropriate wires. This schematic is provided free of charge and may not be 100% accurate. Failure to properly test all the wires may lead to vehicle or bodily damage. All information is provided as-is and accuracy is not guaranteed.

2010 Honda RIdgeline Audio Radio WIring
2010 Honda RIdgeline Audio Radio WIring

If you find any conflicting info please leave a comment with what you found in your 2011 Honda Ridgeline. If you don’t see the audio radio wiring diagram you need comment and we will try to add it ASAP. Thanks for looking!

(MAKE SURE TO SCROLL TO THE BOTTOM TO SEE IF ANY OTHER READERS POSTED ANY OTHER TIPS AND TRICKS!)

2010 Honda Ridgeline Audio Wiring Radio Diagram Schematic Colors

Car Radio Constant 12v+ Wire: White – Pin 24
Car Stereo Ground Wire: Black – Pin 12
Car Radio Ignition Switched Wire: Yellow/Red Pin 14 @ Radio Harness

Car Stereo VSS Speed Wire: N/A
Car Stereo Reverse Wire + : Green (+) @ Light
Car Stereo Dimmer Wire: Red @ Pin 1
Car Radio Illumination Wire: Red/Black (Parking Lights) @ Pin 13
Car Stereo Power Antenna: Black (+) Pin 3 @ Antenna Plug
Car Radio Amp Turn On Wire: N/A

Left Front Speaker Wire (+) Positive: Light Green – Pin 23
Left Front Speaker Wire (-) Negative: Violet – Pin 22
Right Front Speaker Wire (+) Positive: Blue – Pin 19
Right Front Speaker Wire (-) Negative: Red – Pin 18

Left Rear Speaker Wire (+) Positive: Brown/White – Pin 11
Left Rear Speaker Wire (-) Negative: Red/Yellow – Pin 10
Right Rear Speaker Wire (+) Positive: Red/Blue – Pin 7
Right Rear Speaker Wire (-) Negative: Yellow – Pin 6

Center Channel Speaker Wire Positive / Negative: N/A

Subwoofer Speaker Wire Positive / Negative: Yellow/Black & Light Green/Red

These wires let you keep your OEM aux jack to work with your new aftermarket radio. Grab a cheap RCA Auxiliary Cable plug either the aux or the rcas into the back of your new aftermarket radio depending on what type of audio input they have. Then cut off the other end and splice into the following wires at the 14-pin connector found behind the radio:

OEM AUX Audio Left Signal: White @ 14 pin connector pin 1
OEM AUX Audio Left Ground: Red @ 14 pin connector pin 2
OEM AUX Audio Right Signal: Brown @ 14 pin connector pin 8
OEM AUX Audio Right Ground Red @ 14 pin connector pin 2

Radio Size: Single or Double Din

Speaker Size Front: 6.5″
Speaker Size Rear: 6.5″
Speaker Size Subwoofer: 8″

Use the adapters below to install common 6.5″ speakers in the doors. Depending on the size and depth of speakers you still may need to cut some of the door metal away. Use some tin snips to easily get the job done.

Check out these Infinity Reference 6.5-Inch speakers they work great and are an excellent bang for the buck! Or the component version if you want to replace your OEM tweeters in the dash as well.

Radio Removal: Using plastic bezel removal tools carefully pop the radio bezel from the dash. Unplug all the connectors and remove the dash bezel. The radio and pocket below is then held in with 5 screws.

Keep in mind if you are installing a new radio you need the mounting kit, the wiring harness, the antenna adapter, and the steering wheel control adapter if you have audio controls on the wheel you want to keep.

REQUIRED PARTS FOR AFTERMARKET RADIO INSTALL

WIRING HARNESS:

GRAY MOUNTING KIT FOR DOUBLE DIN AFTERMARKET RADIOS:

TAN MOUNTING KIT FOR DOUBLE DIN AFTERMARKET RADIOS:

GRAY MOUNTING KIT FOR SINGLE DIN AFTERMARKET RADIOS:

TAN MOUNTING KIT FOR SINGLE DIN AFTERMARKET RADIOS:

ANTENNA ADAPTER FOR INSTALL:

CUSTOM UNDER SEAT BOX ENCLOSURE FOR ADDING AFTERMARKET SUB WOOFER:

SPEAKER WIRING ADAPTER FOR INSTALL:

Use these if you don’t want to tap in or cut off your existing speaker connectors. They plug right in then right on to the new speaker making installation a breeze. Order quantity 2 if doing front and rear speakers.

STEERING WHEEL CONTROLS ADAPTER:

Metra Axxess ASWC-1 Universal Steering Wheel Control Interface

RECOMMENDED TOOLS FOR THE INSTALL – SAME ONES THE PROS USE!

– Install Bay Butt Connectors

– Gardner Bender Auto Wire Stripper

– 3M Electrical Tape

– Dash Removal Plastic Pry Tools

– Klein Wire Cutters / Crimpers

2011 Honda Ridgeline Audio Radio Wiring Diagram Schematic Colors

Here is the stereo radio wiring information for your 2011 Honda Ridgeline with the standard or amplified systems. It will be useful when installing an aftermarket radio, sound stereo system, or other automotive accessories. Make sure to grab the appropriate tools to test all the wires in your Ridgeline. Please check it over and use it as a GUIDE to help you locate the appropriate wires. This schematic is provided free of charge and may not be 100% accurate. Failure to properly test all the wires may lead to vehicle or bodily damage. All information is provided as-is and accuracy is not guaranteed.

2011 Honda RIdgeline Audio Wiring
2011 Honda RIdgeline Audio Wiring

If you find any conflicting info please leave a comment with what you found in your 2011 Honda Ridgeline. If you don’t see the audio radio wiring diagram you need comment and we will try to add it ASAP. Thanks for looking!

(MAKE SURE TO SCROLL TO THE BOTTOM TO SEE IF ANY OTHER READERS POSTED ANY OTHER TIPS AND TRICKS!)

2011 Honda Ridgeline Audio Wiring Radio Diagram Schematic Colors

Car Radio Constant 12v+ Wire: White – Pin 24
Car Stereo Ground Wire: Black – Pin 12
Car Radio Ignition Switched Wire: Yellow/Red Pin 14 @ Radio Harness

Car Stereo VSS Speed Wire: N/A
Car Stereo Reverse Wire + : Green (+) @ Light
Car Stereo Dimmer Wire: Red @ Pin 1
Car Radio Illumination Wire: Red/Black (Parking Lights) @ Pin 13
Car Stereo Power Antenna: Black (+) Pin 3 @ Antenna Plug
Car Radio Amp Turn On Wire: N/A

Left Front Speaker Wire (+) Positive: Light Green – Pin 23
Left Front Speaker Wire (-) Negative: Violet – Pin 22
Right Front Speaker Wire (+) Positive: Blue – Pin 19
Right Front Speaker Wire (-) Negative: Red – Pin 18

Left Rear Speaker Wire (+) Positive: Brown/White – Pin 11
Left Rear Speaker Wire (-) Negative: Red/Yellow – Pin 10
Right Rear Speaker Wire (+) Positive: Red/Blue – Pin 7
Right Rear Speaker Wire (-) Negative: Yellow – Pin 6

Center Channel Speaker Wire Positive / Negative: N/A

Subwoofer Speaker Wire Positive / Negative: Yellow/Black & Light Green/Red

These wires let you keep your OEM aux jack to work with your new aftermarket radio. Grab a cheap RCA Auxiliary Cable plug either the aux or the rcas into the back of your new aftermarket radio depending on what type of audio input they have. Then cut off the other end and splice into the following wires at the 14-pin connector found behind the radio:

OEM AUX Audio Left Signal: White @ 14 pin connector pin 1
OEM AUX Audio Left Ground: Red @ 14 pin connector pin 2
OEM AUX Audio Right Signal: Brown @ 14 pin connector pin 8
OEM AUX Audio Right Ground Red @ 14 pin connector pin 2

Radio Size: Single or Double Din

Speaker Size Front: 6.5″
Speaker Size Rear: 6.5″
Speaker Size Subwoofer: 8″

Use the adapters below to install common 6.5″ speakers in the doors. Depending on the size and depth of speakers you still may need to cut some of the door metal away. Use some tin snips to easily get the job done.

Check out these Infinity Reference 6.5-Inch speakers they work great and are an excellent bang for the buck! Or the component version if you want to replace your OEM tweeters in the dash as well.

Radio Removal: Using plastic bezel removal tools carefully pop the radio bezel from the dash. Unplug all the connectors and remove the dash bezel. The radio and pocket below is then held in with 5 screws.

Keep in mind if you are installing a new radio you need the mounting kit, the wiring harness, the antenna adapter, and the steering wheel control adapter if you have audio controls on the wheel you want to keep.

REQUIRED PARTS FOR AFTERMARKET RADIO INSTALL

WIRING HARNESS:

GRAY MOUNTING KIT FOR DOUBLE DIN AFTERMARKET RADIOS:

TAN MOUNTING KIT FOR DOUBLE DIN AFTERMARKET RADIOS:

GRAY MOUNTING KIT FOR SINGLE DIN AFTERMARKET RADIOS:

TAN MOUNTING KIT FOR SINGLE DIN AFTERMARKET RADIOS:

CUSTOM UNDER SEAT BOX ENCLOSURE FOR ADDING AFTERMARKET SUB WOOFER:

ANTENNA ADAPTER FOR INSTALL:

SPEAKER WIRING ADAPTER FOR INSTALL:

Use these if you don’t want to tap in or cut off your existing speaker connectors. They plug right in then right on to the new speaker making installation a breeze. Order quantity 2 if doing front and rear speakers.

STEERING WHEEL CONTROLS ADAPTER:

Metra Axxess ASWC-1 Universal Steering Wheel Control Interface

RECOMMENDED TOOLS FOR THE INSTALL – SAME ONES THE PROS USE!

– 3M Electrical Tape

– Dash Removal Plastic Pry Tools

– Klein Wire Cutters / Crimpers

– Install Bay Butt Connectors

– Gardner Bender Auto Wire Stripper

2012 Honda Ridgeline Audio Radio Wiring Diagram Schematic Colors

Here is the stereo radio wiring information for your 2012 Honda Ridgeline with the standard or amplified systems. It will be useful when installing an aftermarket radio, sound stereo system, or other automotive accessories. Make sure to grab the appropriate tools to test all the wires in your Ridgeline. Please check it over and use it as a GUIDE to help you locate the appropriate wires. This schematic is provided free of charge and may not be 100% accurate. Failure to properly test all the wires may lead to vehicle or bodily damage. All information is provided as-is and accuracy is not guaranteed.

2012 Honda Ridgeline Radio Audio Wiring
2012 Honda Ridgeline Radio Wiring

If you find any conflicting info please leave a comment with what you found in your 2012 Honda Ridgeline. If you don’t see the audio radio wiring diagram you need comment and we will try to add it ASAP. Thanks for looking!

(MAKE SURE TO SCROLL TO THE BOTTOM TO SEE IF ANY OTHER READERS POSTED ANY OTHER TIPS AND TRICKS!)

2012 Honda Ridgeline Audio Wiring Radio Diagram Schematic Colors

Car Radio Constant 12v+ Wire: White – Pin 24
Car Stereo Ground Wire: Black – Pin 12
Car Radio Ignition Switched Wire: Yellow/Red Pin 14 @ Radio Harness

Car Stereo VSS Speed Wire: N/A
Car Stereo Reverse Wire + : Green (+) @ Light
Car Stereo Dimmer Wire: Red @ Pin 1
Car Radio Illumination Wire: Red/Black (Parking Lights) @ Pin 13
Car Stereo Power Antenna: Black (+) Pin 3 @ Antenna Plug
Car Radio Amp Turn On Wire: N/A

Left Front Speaker Wire (+) Positive: Light Green – Pin 23
Left Front Speaker Wire (-) Negative: Violet – Pin 22
Right Front Speaker Wire (+) Positive: Blue – Pin 19
Right Front Speaker Wire (-) Negative: Red – Pin 18

Left Rear Speaker Wire (+) Positive: Brown/White – Pin 11
Left Rear Speaker Wire (-) Negative: Red/Yellow – Pin 10
Right Rear Speaker Wire (+) Positive: Red/Blue – Pin 7
Right Rear Speaker Wire (-) Negative: Yellow – Pin 6

Center Channel Speaker Wire Positive / Negative: N/A

Subwoofer Speaker Wire Positive / Negative: Yellow/Black & Light Green/Red

These wires let you keep your OEM aux jack to work with your new aftermarket radio. Grab a cheap RCA Auxiliary Cable plug either the aux or the rcas into the back of your new aftermarket radio depending on what type of audio input they have. Then cut off the other end and splice into the following wires at the 14-pin connector found behind the radio:

OEM AUX Audio Left Signal: White @ 14 pin connector pin 1
OEM AUX Audio Left Ground: Red @ 14 pin connector pin 2
OEM AUX Audio Right Signal: Brown @ 14 pin connector pin 8
OEM AUX Audio Right Ground Red @ 14 pin connector pin 2

Radio Size: Single or Double Din

Speaker Size Front: 6.5″
Speaker Size Rear: 6.5″
Speaker Size Subwoofer: 8″

Use the adapters below to install common 6.5″ speakers in the doors. Depending on the size and depth of speakers you still may need to cut some of the door metal away. Use some tin snips to easily get the job done.

Check out these Infinity Reference 6.5-Inch speakers they work great and are an excellent bang for the buck! Or the component version if you want to replace your OEM tweeters in the dash as well.

Radio Removal: Using plastic bezel removal tools carefully pop the radio bezel from the dash. Unplug all the connectors and remove the dash bezel. The radio and pocket below is then held in with 5 screws.

Keep in mind if you are installing a new radio you need the mounting kit, the wiring harness, the antenna adapter, and the steering wheel control adapter if you have audio controls on the wheel you want to keep.

REQUIRED PARTS FOR AFTERMARKET RADIO INSTALL

WIRING HARNESS:

GRAY MOUNTING KIT FOR DOUBLE DIN AFTERMARKET RADIOS:

TAN MOUNTING KIT FOR DOUBLE DIN AFTERMARKET RADIOS:

GRAY MOUNTING KIT FOR SINGLE DIN AFTERMARKET RADIOS:

TAN MOUNTING KIT FOR SINGLE DIN AFTERMARKET RADIOS:

CUSTOM UNDER SEAT BOX ENCLOSURE FOR ADDING AFTERMARKET SUB WOOFER:

ANTENNA ADAPTER FOR INSTALL:

SPEAKER WIRING ADAPTER FOR INSTALL:

Use these if you don’t want to tap in or cut off your existing speaker connectors. They plug right in then right on to the new speaker making installation a breeze. Order quantity 2 if doing front and rear speakers.

STEERING WHEEL CONTROLS ADAPTER:

Metra Axxess ASWC-1 Universal Steering Wheel Control Interface

RECOMMENDED TOOLS FOR THE INSTALL – SAME ONES THE PROS USE!

– 3M Electrical Tape

– Install Bay Butt Connectors

– Gardner Bender Auto Wire Stripper

– Dash Removal Plastic Pry Tools

– Klein Wire Cutters / Crimpers

2013 Honda Ridgeline Audio Radio Wiring Diagram Schematic Colors

Here is the stereo radio wiring information for your 2013 Honda Ridgeline with the standard or amplified systems. It will be useful when installing an aftermarket radio, sound stereo system, or other automotive accessories. Make sure to grab the appropriate tools to test all the wires in your Ridgeline. Please check it over and use it as a GUIDE to help you locate the appropriate wires. This schematic is provided free of charge and may not be 100% accurate. Failure to properly test all the wires may lead to vehicle or bodily damage. All information is provided as-is and accuracy is not guaranteed.

2013 Honda Ridgeline Audio Wiring
2013 Honda Ridgeline Audio Wiring

If you find any conflicting info please leave a comment with what you found in your 2013 Honda Ridgeline. If you don’t see the audio radio wiring diagram you need comment and we will try to add it ASAP. Thanks for looking!

(MAKE SURE TO SCROLL TO THE BOTTOM TO SEE IF ANY OTHER READERS POSTED ANY OTHER TIPS AND TRICKS!)

2013 Honda Ridgeline Audio Wiring Radio Diagram Schematic Colors

Car Radio Constant 12v+ Wire: White – Pin 24
Car Stereo Ground Wire: Black – Pin 12
Car Radio Ignition Switched Wire: Yellow/Red Pin 14 @ Radio Harness

Car Stereo VSS Speed Wire: N/A
Car Stereo Reverse Wire + : Green (+) @ Light
Car Stereo Dimmer Wire: Red @ Pin 1
Car Radio Illumination Wire: Red/Black (Parking Lights) @ Pin 13
Car Stereo Power Antenna: Black (+) Pin 3 @ Antenna Plug
Car Radio Amp Turn On Wire: N/A

Left Front Speaker Wire (+) Positive: Light Green – Pin 23
Left Front Speaker Wire (-) Negative: Violet – Pin 22
Right Front Speaker Wire (+) Positive: Blue – Pin 19
Right Front Speaker Wire (-) Negative: Red – Pin 18

Left Rear Speaker Wire (+) Positive: Brown/White – Pin 11
Left Rear Speaker Wire (-) Negative: Red/Yellow – Pin 10
Right Rear Speaker Wire (+) Positive: Red/Blue – Pin 7
Right Rear Speaker Wire (-) Negative: Yellow – Pin 6

Center Channel Speaker Wire Positive / Negative: N/A

Subwoofer Speaker Wire Positive / Negative: Yellow/Black & Light Green/Red

These wires let you keep your OEM aux jack to work with your new aftermarket radio. Grab a cheap RCA Auxiliary Cable plug either the aux or the rcas into the back of your new aftermarket radio depending on what type of audio input they have. Then cut off the other end and splice into the following wires at the 14-pin connector found behind the radio:

OEM AUX Audio Left Signal: White @ 14 pin connector pin 1
OEM AUX Audio Left Ground: Red @ 14 pin connector pin 2
OEM AUX Audio Right Signal: Brown @ 14 pin connector pin 8
OEM AUX Audio Right Ground Red @ 14 pin connector pin 2

Radio Size: Single or Double Din

Speaker Size Front: 6.5″
Speaker Size Rear: 6.5″
Speaker Size Subwoofer: 8″

Use the adapters below to install common 6.5″ speakers in the doors. Depending on the size and depth of speakers you still may need to cut some of the door metal away. Use some tin snips to easily get the job done.

Check out these Infinity Reference 6.5-Inch speakers they work great and are an excellent bang for the buck! Or the component version if you want to replace your OEM tweeters in the dash as well.

Radio Removal: Using plastic bezel removal tools carefully pop the radio bezel from the dash. Unplug all the connectors and remove the dash bezel. The radio and pocket below is then held in with 5 screws.

Keep in mind if you are installing a new radio you need the mounting kit, the wiring harness, the antenna adapter, and the steering wheel control adapter if you have audio controls on the wheel you want to keep.

REQUIRED PARTS FOR AFTERMARKET RADIO INSTALL

WIRING HARNESS:

GRAY MOUNTING KIT FOR SINGLE DIN AFTERMARKET RADIOS:

TAN MOUNTING KIT FOR SINGLE DIN AFTERMARKET RADIOS:


GRAY MOUNTING KIT FOR DOUBLE DIN AFTERMARKET RADIOS:

TAN MOUNTING KIT FOR DOUBLE DIN AFTERMARKET RADIOS:

CUSTOM UNDER SEAT BOX ENCLOSURE FOR ADDING AFTERMARKET SUB WOOFER:

ANTENNA ADAPTER FOR INSTALL:

SPEAKER WIRING ADAPTER FOR INSTALL:

Use these if you don’t want to tap in or cut off your existing speaker connectors. They plug right in then right on to the new speaker making installation a breeze. Order quantity 2 if doing front and rear speakers.

STEERING WHEEL CONTROLS ADAPTER:

Metra Axxess ASWC-1 Universal Steering Wheel Control Interface

RECOMMENDED TOOLS FOR THE INSTALL – SAME ONES THE PROS USE!

– 3M Electrical Tape

– Install Bay Butt Connectors

– Gardner Bender Auto Wire Stripper

– Klein Wire Cutters / Crimpers

– Dash Removal Plastic Pry Tools

2014 Honda Ridgeline Audio Radio Wiring Diagram Schematic Colors

Here is the stereo radio wiring information for your 2014 Honda Ridgeline with the standard or amplified systems. It will be useful when installing an aftermarket radio, sound stereo system, or other automotive accessories. Make sure to grab the appropriate tools to test all the wires in your Ridgeline. Please check it over and use it as a GUIDE to help you locate the appropriate wires. This schematic is provided free of charge and may not be 100% accurate. Failure to properly test all the wires may lead to vehicle or bodily damage. All information is provided as-is and accuracy is not guaranteed.

2014 Honda Ridgeline Audio Radio WIring
2014 Honda Ridgeline Audio Radio Wiring

If you find any conflicting info please leave a comment with what you found in your 2014 Honda Ridgeline. If you don’t see the audio radio wiring diagram you need comment and we will try to add it ASAP. Thanks for looking!

(MAKE SURE TO SCROLL TO THE BOTTOM TO SEE IF ANY OTHER READERS POSTED ANY OTHER TIPS AND TRICKS!)

2014 Honda Ridgeline Audio Wiring Radio Diagram Schematic Colors

Car Radio Constant 12v+ Wire: White – Pin 24
Car Stereo Ground Wire: Black – Pin 12
Car Radio Ignition Switched Wire: Yellow/Red Pin 14 @ Radio Harness

Car Stereo VSS Speed Wire: N/A
Car Stereo Reverse Wire + : Green (+) @ Light
Car Stereo Dimmer Wire: Red @ Pin 1
Car Radio Illumination Wire: Red/Black (Parking Lights) @ Pin 13
Car Stereo Power Antenna: Black (+) Pin 3 @ Antenna Plug
Car Radio Amp Turn On Wire: N/A

Left Front Speaker Wire (+) Positive: Light Green – Pin 23
Left Front Speaker Wire (-) Negative: Violet – Pin 22
Right Front Speaker Wire (+) Positive: Blue – Pin 19
Right Front Speaker Wire (-) Negative: Red – Pin 18

Left Rear Speaker Wire (+) Positive: Brown/White – Pin 11
Left Rear Speaker Wire (-) Negative: Red/Yellow – Pin 10
Right Rear Speaker Wire (+) Positive: Red/Blue – Pin 7
Right Rear Speaker Wire (-) Negative: Yellow – Pin 6

Center Channel Speaker Wire Positive / Negative: N/A

Subwoofer Speaker Wire Positive / Negative: Yellow/Black & Light Green/Red

These wires let you keep your OEM aux jack to work with your new aftermarket radio. Grab a cheap RCA Auxiliary Cable plug either the aux or the rcas into the back of your new aftermarket radio depending on what type of audio input they have. Then cut off the other end and splice into the following wires at the 14-pin connector found behind the radio:

OEM AUX Audio Left Signal: White @ 14 pin connector pin 1
OEM AUX Audio Left Ground: Red @ 14 pin connector pin 2
OEM AUX Audio Right Signal: Brown @ 14 pin connector pin 8
OEM AUX Audio Right Ground Red @ 14 pin connector pin 2

Radio Size: Single or Double Din

Speaker Size Front: 6.5″
Speaker Size Rear: 6.5″
Speaker Size Subwoofer: 8″

Use the adapters below to install common 6.5″ speakers in the doors. Depending on the size and depth of speakers you still may need to cut some of the door metal away. Use some tin snips to easily get the job done.

Check out these Infinity Reference 6.5-Inch speakers they work great and are an excellent bang for the buck! Or the component version if you want to replace your OEM tweeters in the dash as well.

Radio Removal: Using plastic bezel removal tools carefully pop the radio bezel from the dash. Unplug all the connectors and remove the dash bezel. The radio and pocket below is then held in with 5 screws.

Keep in mind if you are installing a new radio you need the mounting kit, the wiring harness, the antenna adapter, and the steering wheel control adapter if you have audio controls on the wheel you want to keep.

REQUIRED PARTS FOR AFTERMARKET RADIO INSTALL

WIRING HARNESS:

TAN MOUNTING KIT FOR SINGLE DIN AFTERMARKET RADIOS:

GRAY MOUNTING KIT FOR SINGLE DIN AFTERMARKET RADIOS:

GRAY MOUNTING KIT FOR DOUBLE DIN AFTERMARKET RADIOS:

TAN MOUNTING KIT FOR DOUBLE DIN AFTERMARKET RADIOS:

CUSTOM UNDER SEAT BOX ENCLOSURE FOR ADDING AFTERMARKET SUB WOOFER:

ANTENNA ADAPTER FOR INSTALL:

SPEAKER WIRING ADAPTER FOR INSTALL:

Use these if you don’t want to tap in or cut off your existing speaker connectors. They plug right in then right on to the new speaker making installation a breeze. Order quantity 2 if doing front and rear speakers.

STEERING WHEEL CONTROLS ADAPTER:

Metra Axxess ASWC-1 Universal Steering Wheel Control Interface

RECOMMENDED TOOLS FOR THE INSTALL – SAME ONES THE PROS USE!

– 3M Electrical Tape

– Install Bay Butt Connectors

– Dash Removal Plastic Pry Tools

– Gardner Bender Auto Wire Stripper

– Klein Wire Cutters / Crimpers

2008 Ford F-150 Audio Radio Wiring Diagram Schematic Colors

Here is the stereo radio wiring information for your 2008 Ford F-150 F150 body with the standard or amplified systems. It will be useful when installing an aftermarket radio, sound stereo system, or other automotive accessories. Make sure to grab the appropriate tools to test all the wires in your F-150 Pickup. Please check it over and use it as a GUIDE to help you locate the appropriate wires. This schematic is provided free of charge and may not be 100% accurate. Failure to properly test all the wires may lead to vehicle or bodily damage. All information is provided as-is and accuracy is not guaranteed.

2008 Ford F-150 Audio Wiring Diagram Radio Schematic Colors
2008 Ford F-150 Audio Wiring Diagram Radio Schematic Colors

If you find any conflicting info please leave a comment with what you found in your 2 or 4 door 2008 Ford F-150. If you don’t see the audio radio wiring diagram you need comment and we will try to add it ASAP. Thanks for looking!

2008 Ford F-150 & FX4 Audio Wiring Radio Diagram Schematic Colors

Car Radio Constant 12v+ Wire: Light Green/Violet
Car Stereo Ground Wire: Black/Green or Black
Car Radio Ignition Switched Wire: Light Green/Yellow or Pink/Black @ Radio Harness

Car Stereo VSS Speed Wire: Gray/Black @ Main Radio Plug
Car Stereo Reverse Wire + : Pink/Black or Green/Yellow @ Driver door sill harness
Car Stereo Dimmer Wire: Light Blue/Red @ Main Radio Harness
Car Radio Illumination Wire: Brown (Park Lights) @ Driver door sill harness
Car Stereo Power Antenna:
Car Radio Amp Turn On Wire: Dark Green/Violet @ Smaller Amp Plug behind radio

Left Front Speaker Wire (+) Positive: Orange/Light Green
Left Front Speaker Wire (-) Negative: Light Blue/White
Right Front Speaker Wire (+) Positive: White/Light Green
Right Front Speaker Wire (-) Negative: Dark Green/Orange

Left Rear Speaker Wire (+) Positive: Gray/Light Blue
Left Rear Speaker Wire (-) Negative: Tan/Yellow
Right Rear Speaker Wire (+) Positive: Orange/Red
Right Rear Speaker Wire (-) Negative: Brown/Pink

Center Channel Speaker Wire Positive / Negative: N/A

Subwoofer Speaker Wire Positive / Negative: Brown/Orange & Red/Black

OEM AUX Audio Left Signal: Red @ 16 pin connector pin 7
OEM AUX Audio Left Ground: White @ 16 pin connector pin 8
OEM AUX Audio Right Signal: Orange @ 16 pin connector pin 6
OEM AUX Audio Right Ground Pink @ 16 pin connector pin 14

USE THIS HARNESS TO AVOID SPLICING IF YOU WANT TO USE THE OEM AUX JACK WITH YOUR NEW AFTERMARKET RADIO: Metra 70-5520AUX Auxiliary Input Retention Harness for Select Ford Vehicles

Radio Size: Single or Double Din

Speaker Size Front: 6×8″
Speaker Size Rear: 6×8″

You may also use the adapters below to install common 6.5″ speakers in the 6×8″ locations:

Radio Removal: Using plastic bezel removal tools carefully pop the radio bezel from the dash. Unplug all the connectors and remove the dash bezel. The radio is then held in with 4 7mm screws.

Keep in mind if you are installing a new radio you need the radio removal keys, the wiring harness, the antenna adapter, and the mounting kit as well. During installation we recommend removing some of the plastic behind the OEM radio to help fit the new aftermarket radio all the way in the dash.

REQUIRED PARTS FOR AFTERMARKET RADIO INSTALL

WIRING HARNESS WITHOUT OEM SUBWOOFER:

WIRING HARNESS WITH OEM SUB WOOFER:

MOUNTING KIT FOR SINGLE DIN AFTERMARKET RADIOS:

MOUNTING KIT FOR DOUBLE DIN AFTERMARKET RADIOS:

OEM AMP TURN ON POP FIX :

If you’re experiencing a loud pop through your F150 sub when the radio turns on and off, this interface will correct the issue by stepping down the turn on voltage to your OEM amplifier.

CUSTOM UNDER SEAT BOX ENCLOSURE FOR ADDING AFTERMARKET SUB WOOFER:

RETAIN YOUR OEM AUX JACK WITH THE NEW RADIO:

ANTENNA ADAPTER FOR INSTALL:

Only required for trucks 2007 and up. No adapter required for pre 2007 Ford F-150

SPEAKER WIRING ADAPTER FOR INSTALL:

Use these if you don’t want to tap in or cut off your existing speaker connectors. They plug right in then right on to the new speaker making installation a breeze. Order quantity 2 if doing front and rear speakers.

STEERING WHEEL CONTROLS ADAPTER:

Metra Axxess ASWC-1 Universal Steering Wheel Control Interface

RECOMMENDED TOOLS FOR THE INSTALL – SAME ONES THE PROS USE!

– 3M Electrical Tape

– Install Bay Butt Connectors

– Dash Removal Plastic Pry Tools

– Gardner Bender Auto Wire Stripper

– Klein Wire Cutters / Crimpers